Set the start volume and level the sound

Updated Oct 29, 2026 · 5 min read · All plans

This article shows you how to choose how loud your video starts, let returning viewers keep the volume they chose, and make every video play at the same loudness however it was recorded.

Available on: every plan. Testing start volumes against each other comes with Pro, Business and Agency: see A/B test your video.

Start volume

The start volume is how loud the sound is when it starts: when the viewer clicks play, or when they turn the sound on after the video started muted (see Start the video automatically with a sound button). It goes from 10% to 100% in steps of 5. New videos start at 100%.

  1. Go to Videos and open your video.
  2. Click the Behavior tab.
  3. Under Sound, move the Start volume slider.
  4. Click Hear it to hear a short sample at that volume. Click Stop to stop it early.

The sample is a short chime played by PlayerMagick in your browser, not your video. It lets you compare, say, 60% with 100% before you save. Your video's own sound may be louder or quieter than the sample: to make every video equally loud, turn on Level the sound (below).

Changes are saved automatically and reach your page within a minute. You do not need to copy the embed code again.

iPhone and iPad set the volume with their own buttons: a website can't change it there, so the start volume has no effect on them. Viewers there hear the volume their device is set to.

Remember each viewer's volume

With Remember each viewer's volume on (new videos have it on), a viewer who changed the volume finds it the same next time, on every PlayerMagick video of the same website. It is kept in their browser, for your website only: never in a cookie, never in a link, and nothing is sent to PlayerMagick.

  • A viewer who never touched the volume starts at your start volume.
  • Muting does not change the remembered volume: the next time they click play, the sound starts at the volume they had.
  • Turn it off and everyone always starts at your start volume, even viewers who changed it before.
  • Clearing the browser's site data forgets the volume.

Level the sound

Videos recorded on different days, microphones or phones often play at very different loudness: one is too quiet, the next one too loud. Level the sound to a standard loudness makes every video play at the same loudness: −16 LUFS, the level most streaming services use. It is done while your video is converted, so it uses no extra conversion hours.

  • New videos are levelled when Level the sound of new videos is on in Settings → Plan and usage → Defaults for new videos. It is on unless you turn it off. The upload dialog shows what new videos get: "Sound levelled to a standard loudness" or "Sound kept as recorded", with a link to change it.
  • Videos you already have keep their sound. To level one, turn on Level the sound to a standard loudness in its Behavior tab and convert it again (below).
  • A video without sound, or a silent one, has nothing to level and stays as it is.
  • Levelling makes the whole video louder or quieter at once, like turning one knob. It does not change the balance inside the video, and it keeps peaks below the level where the sound would distort.

Convert a video again

Turning Level the sound on or off for a video you already have says Applies the next time this video is converted.

  1. Click Convert again now.
  2. PlayerMagick converts your current video file again, with the sound levelled (or as recorded, if you turned it off). The progress shows under the switch: "Converting with the sound levelled · about 2 min left".
  3. Viewers keep getting the current version until the new one is ready. You can leave the editor.
  4. When it is done, the section says The sound is levelled. Converted again on that day.

Converting again is included in your plan, at no extra cost. One conversion of a video runs at a time.

Good to know

  • The start volume applies to computers and Android phones and tablets. On iPhone and iPad the device's own volume applies.
  • In a funnel, each step video starts at its own start volume, and a remembered volume carries from step to step.
  • The volume a viewer remembers is per website, not per video: changing it on one of your videos applies to your other videos on the same site.
  • Hear it needs your computer's sound on. If you hear nothing, check your computer's volume and that the browser tab is not muted.

Troubleshooting

  • My video still starts at full volume on my iPhone. That is expected: iPhone and iPad don't let websites change the volume.
  • A viewer says the video starts too quietly. They may have turned it down on your site before: with Remember each viewer's volume on, their own choice wins. It is kept until they change it again or clear their browser data.
  • Convert again now says the video is already being converted. Wait until the current conversion finishes, then try again.
  • Convert again now says conversions are paused. This is rare. Your video keeps playing as it is. Convert it again on the date shown, or write to support if you need it sooner.
  • The video is still quiet after levelling. Check that the section says "The sound is levelled". If the video was very quiet, levelling raises it only as far as its loudest moments allow without distortion.

Was this article helpful?